From 84f8f93e8e861aac9770ff52c3135cdfc148f61d Mon Sep 17 00:00:00 2001 From: Chad Schwieterman <chad.devops@gmail.com> Date: Tue, 2 Feb 2021 18:14:11 -0500 Subject: [PATCH] config: Add printer config for the Ender 3 Max by Creality3D (#3879) Added Ender 3 Max config. Based off the configs from ender6, ender3-v2, and ender3. Also contains optional BLTouch parameters. Signed-off-by: Chad Schwieterman <chad.devops@gmail.com> --- config/printer-creality-ender3max-2021.cfg | 150 +++++++++++++++++++++ 1 file changed, 150 insertions(+) create mode 100644 config/printer-creality-ender3max-2021.cfg diff --git a/config/printer-creality-ender3max-2021.cfg b/config/printer-creality-ender3max-2021.cfg new file mode 100644 index 000000000..fa7559d7f --- /dev/null +++ b/config/printer-creality-ender3max-2021.cfg @@ -0,0 +1,150 @@ +# This file contains pin mappings for the stock 2020 Creality Ender 3 +# MAX. To use this config, during "make menuconfig" select the +# STM32F103 with a "28KiB bootloader" and with "Use USB for +# communication" disabled. + +# Because this printer has factory wiring, mounts, and firmware for +# a BLTouch, but does not ship with one at this time, default values +# for the sensor have been specified, but disabled, in anticipation of +# future revisions or user modification. User should take care to +# customize the offsets, particularly z-offset, for their specific unit. + +# If you prefer a direct serial connection, in "make menuconfig" +# select "Enable extra low-level configuration options" and select the +# USART3 serial port, which is broken out on the 10 pin IDC cable used +# for the LCD module as follows: +# 3: Tx, 4: Rx, 9: GND, 10: VCC + +# Flash this firmware by copying "out/klipper.bin" to a SD card and +# turning on the printer with the card inserted. The firmware +# filename must end in ".bin" and must not match the last filename +# that was flashed. + +# See docs/Config_Reference.md for a description of parameters. + +[stepper_x] +step_pin: PC2 +dir_pin: PB9 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA5 +position_endstop: 0 +position_max: 300 +homing_speed: 50 + +[stepper_y] +step_pin: PB8 +dir_pin: PB7 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA6 +position_endstop: 0 +position_max: 300 +homing_speed: 50 + +[stepper_z] +step_pin: PB6 +dir_pin: !PB5 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 8 +position_endstop: 0.0 # disable to use BLTouch +endstop_pin: ^PA7 # disable to use BLTouch +#endstop_pin: probe:z_virtual_endstop # enable to use BLTouch +#position_min: -5 # enable to use BLTouch +position_max: 340 + +# [safe_z_home] # enable for BLTouch +# home_xy_position: 150, 150 +# speed: 100 +# z_hop: 10 +# z_hop_speed: 5 + +# [bltouch] # enable for BLTouch - fast-mode +# sensor_pin: ^PB1 +# control_pin: PB0 +# pin_up_touch_mode_reports_triggered: True +# probe_with_touch_mode: True +# x_offset: 50 # modify as needed for bltouch location +# y_offset: -6 # modify as needed for bltouch location +# z_offset: 0.0 # modify as needed for bltouch or run PROBE_CALIBRATE +# speed: 10 +# samples: 3 +# sample_retract_dist: 5.0 # Can be set lower, example 2.5 depending on height of bltouch from bed +# lift_speed: 40 +# samples_tolerance_retries: 3 +# speed: 10 +# samples: 2 + +# [bed_mesh] # enable for BLTouch +# speed: 300 +# mesh_min: 50, 0 +# mesh_max: 290, 290 +# algorithm: bicubic +# probe_count: 7,7 # 49 points due to large bed size +# horizontal_move_z: 5 + + +# [gcode_macro G29] # If moving from marlin to klipper uncomment to mimic G29 +# gcode: +# BED_MESH_CALIBRATE +# G1 X0 Y0 Z10 F4000 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB4 +dir_pin: PB3 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 31.901 # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC5 +control: pid +pid_Kp: 21.527 +pid_Ki: 1.063 +pid_Kd: 108.982 +min_temp: 0 +max_temp: 250 +pressure_advance: 0.0 # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Pressure_Advance.md + + +[heater_bed] +heater_pin: PA2 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC4 +control: pid +pid_Kp: 54.027 +pid_Ki: 0.770 +pid_Kd: 948.182 +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA0 + +[filament_switch_sensor e0_sensor] +switch_pin: PA4 + +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 # Run ls /dev/serial/by-id/* for micro-controller name +restart_method: command + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +[display] +lcd_type: st7920 +cs_pin: PB12 +sclk_pin: PB13 +sid_pin: PB15 +encoder_pins: ^PD2, ^PD3 +click_pin: ^!PC0