From 85a1e1118fea8ed12ef7fadb6394edc7f07120ff Mon Sep 17 00:00:00 2001 From: Kevin O'Connor <kevin@koconnor.net> Date: Mon, 24 Jul 2017 12:34:26 -0400 Subject: [PATCH] config: Change default pins defined in example.cfg to use RAMPS pins Change the example.cfg file to use the pins of a RAMPS config as that is a very common setup. Signed-off-by: Kevin O'Connor <kevin@koconnor.net> --- config/example-corexy.cfg | 9 +++---- config/example.cfg | 50 +++++++++++++++++++-------------------- 2 files changed, 27 insertions(+), 32 deletions(-) diff --git a/config/example-corexy.cfg b/config/example-corexy.cfg index 824eb4b0c..ac2b23c68 100644 --- a/config/example-corexy.cfg +++ b/config/example-corexy.cfg @@ -14,9 +14,8 @@ step_pin: ar54 dir_pin: ar55 enable_pin: !ar38 step_distance: .01 -endstop_pin: ^ar2 +endstop_pin: ^ar3 homing_speed: 50.0 -position_min: 0 position_endstop: 0 position_max: 200 @@ -27,9 +26,8 @@ step_pin: ar60 dir_pin: ar61 enable_pin: !ar56 step_distance: .01 -endstop_pin: ^ar15 +endstop_pin: ^ar14 homing_speed: 50.0 -position_min: 0 position_endstop: 0 position_max: 200 @@ -38,8 +36,7 @@ step_pin: ar46 dir_pin: ar48 enable_pin: !ar62 step_distance: .01 -endstop_pin: ^ar19 -position_min: 0.1 +endstop_pin: ^ar18 position_endstop: 0.5 position_max: 200 diff --git a/config/example.cfg b/config/example.cfg index 80bf1daa8..36f609c68 100644 --- a/config/example.cfg +++ b/config/example.cfg @@ -20,19 +20,19 @@ # The stepper_x section is used to describe the stepper controlling # the X axis in a cartesian robot. [stepper_x] -step_pin: ar29 +step_pin: ar54 # Step GPIO pin (triggered high). This parameter must be provided. -dir_pin: !ar28 +dir_pin: ar55 # Direction GPIO pin (high indicates positive direction). This # parameter must be provided. -enable_pin: !ar25 +enable_pin: !ar38 # Enable pin (default is enable high; use ! to indicate enable # low). If this parameter is not provided then the stepper motor # driver must always be enabled. step_distance: .0225 # Distance in mm that each step causes the axis to travel. This # parameter must be provided. -endstop_pin: ^ar0 +endstop_pin: ^ar3 # Endstop switch detection pin. This parameter must be provided for # the X, Y, and Z steppers on cartesian style printers. #homing_speed: 5.0 @@ -64,7 +64,7 @@ endstop_pin: ^ar0 # reset. If this is not set, but homing_stepper_phases is set, then # the stepper phase will be detected on the first home and that # phase will be used on all subsequent homes. -position_min: -0.25 +#position_min: 0 # Minimum valid distance (in mm) the user may command the stepper to # move to. The default is 0mm. position_endstop: 0 @@ -79,12 +79,11 @@ position_max: 200 # the Y axis in a cartesian robot. It has the same settings as the # stepper_x section. [stepper_y] -step_pin: ar27 -dir_pin: ar26 -enable_pin: !ar25 +step_pin: ar60 +dir_pin: !ar61 +enable_pin: !ar56 step_distance: .0225 -endstop_pin: ^ar1 -position_min: -0.25 +endstop_pin: ^ar14 position_endstop: 0 position_max: 200 @@ -92,12 +91,11 @@ position_max: 200 # the Z axis in a cartesian robot. It has the same settings as the # stepper_x section. [stepper_z] -step_pin: ar23 -dir_pin: !ar22 -enable_pin: !ar25 +step_pin: ar46 +dir_pin: ar48 +enable_pin: !ar62 step_distance: .005 -endstop_pin: ^ar2 -position_min: 0.1 +endstop_pin: ^ar18 position_endstop: 0.5 position_max: 200 @@ -107,9 +105,9 @@ position_max: 200 # stepper_x section and the heater configuration has the same settings # as the heater_bed section (described below). [extruder] -step_pin: ar19 -dir_pin: ar18 -enable_pin: !ar25 +step_pin: ar26 +dir_pin: ar28 +enable_pin: !ar24 step_distance: .004242 nozzle_diameter: 0.500 # Diameter of the nozzle orifice (in mm). This parameter must be @@ -164,7 +162,7 @@ filament_diameter: 3.500 # activation. # # The remaining variables describe the extruder heater. -heater_pin: ar4 +heater_pin: ar10 # PWM output pin controlling the heater. This parameter must be # provided. #max_power: 1.0 @@ -177,7 +175,7 @@ heater_pin: ar4 sensor_type: EPCOS 100K B57560G104F # Type of sensor - this may be "EPCOS 100K B57560G104F", "ATC # Semitec 104GT-2", or "AD595". This parameter must be provided. -sensor_pin: analog1 +sensor_pin: analog13 # Analog input pin connected to the sensor. This parameter must be # provided. #pullup_resistor: 4700 @@ -221,16 +219,16 @@ max_temp: 210 # named "extruder1", "extruder2", "extruder3", and so on. See the # "extruder" section above for a description of available parameters. #[extruder1] -#step_pin: ar20 -#dir_pin: ar21 +#step_pin: ar36 +#dir_pin: ar34 #... # The heater_bed section describes a heated bed (if present - omit # section if not present). [heater_bed] -heater_pin: ar3 +heater_pin: ar8 sensor_type: EPCOS 100K B57560G104F -sensor_pin: analog0 +sensor_pin: analog14 control: watermark #max_delta: 2.0 # On 'watermark' controlled heaters this is the number of degrees in @@ -242,7 +240,7 @@ max_temp: 110 # Print cooling fan (omit section if fan not present). [fan] -pin: ar14 +pin: ar9 # PWM output pin controlling the fan. This parameter must be # provided. #max_power: 1.0 @@ -328,7 +326,7 @@ max_z_accel: 30 # whenever its associated heater is active. #[heater_fan my_nozzle_fan] # See the "fan" section for fan configuration parameters. -#pin: ar7 +#pin: ar4 # The remaining variables are specific to heater_fan. #heater: extruder # Name of the config section defining the heater that this fan is