Kevin O'Connor 6c8d1ddaec bltouch: Ensure the z_offset is not negative ...

It would not make sense to have a negative z_offset.  Reported by
@Yoyolick.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2021-06-22 15:30:25 -04:00

..

display

virtual_sdcard: add file_path and file_size to status

2021-06-22 15:15:03 -04:00

__init__.py

…

ad5206.py

…

adc_scaled.py

…

adc_temperature.py

…

adxl345.py

adxl345: Use "clock" suffix instead of "time" in commands

2021-04-30 11:40:37 -04:00

bed_mesh.py

bed_mesh: implement BED_MESH_OFFSET

2021-06-08 00:02:35 -04:00

bed_screws.py

…

bed_tilt.py

…

bltouch.py

bltouch: Ensure the z_offset is not negative

2021-06-22 15:30:25 -04:00

bme280.py

…

board_pins.py

…

bus.py

…

buttons.py

…

canbus_ids.py

…

controller_fan.py

…

delayed_gcode.py

…

delta_calibrate.py

stepper: Remove set_tag_position() code

2021-05-29 21:54:34 -04:00

display_status.py

…

dotstar.py

dotstar: report color data via get_status()

2021-06-18 10:53:12 -04:00

ds18b20.py

…

endstop_phase.py

endstop_phase: Unify phase conversion code

2021-06-06 20:41:27 -04:00

extruder_stepper.py

stepper: Do not set min_stop_interval in micro-controller

2021-04-30 11:09:08 -04:00

fan_generic.py

…

fan.py

…

filament_motion_sensor.py

filament_motion_sensor: add get_status (#4281)

2021-05-11 13:17:22 -04:00

filament_switch_sensor.py

…

firmware_retraction.py

gcode: Update gcode descriptions (#4335)

2021-06-02 10:45:27 -04:00

force_move.py

…

gcode_arcs.py

…

gcode_button.py

…

gcode_macro.py

gcode_macro: add description property (#4317)

2021-05-26 14:21:21 -04:00

gcode_move.py

gcode: Update gcode descriptions (#4335)

2021-06-02 10:45:27 -04:00

hall_filament_width_sensor.py

…

heater_bed.py

…

heater_fan.py

heater_fan: Fix typo causing excessive cpu usage

2020-12-01 12:31:22 -05:00

heater_generic.py

…

heaters.py

…

homing_heaters.py

…

homing_override.py

…

homing.py

homing: Check for failures during multi-endstop homing

2021-06-09 18:58:35 -04:00

htu21d.py

…

idle_timeout.py

…

input_shaper.py

…

lm75.py

…

manual_probe.py

stepper: Remove set_tag_position() code

2021-05-29 21:54:34 -04:00

manual_stepper.py

…

mcp4018.py

…

mcp4451.py

…

mcp4728.py

…

multi_pin.py

…

neopixel.py

neopixel: report color data via get_status() method

2021-06-18 10:53:12 -04:00

output_pin.py

…

palette2.py

…

pause_resume.py

print_stats: add cancelled when CANCEL_PRINT used (#4366)

2021-06-14 15:09:55 -04:00

pca9533.py

…

pid_calibrate.py

…

print_stats.py

print_stats: add cancelled when CANCEL_PRINT used (#4366)

2021-06-14 15:09:55 -04:00

probe.py

probe: Call add_stepper() earlier in boot process

2021-06-09 18:58:35 -04:00

pulse_counter.py

…

quad_gantry_level.py

z_tilt: expose an 'applied' status to allow macros to skip QGL/Z_TILT_ADJUST (#4313)

2021-06-02 11:11:19 -04:00

query_adc.py

…

query_endstops.py

…

replicape.py

…

resonance_tester.py

resonance_tester: Set max_accel ignoring the limit from the config (#4174)

2021-06-06 13:04:53 -04:00

respond.py

gcode: Update gcode descriptions (#4335)

2021-06-02 10:45:27 -04:00

safe_z_home.py

safe_z_home: Simplify logic and fix edge case

2021-05-26 12:57:31 -04:00

samd_sercom.py

…

save_variables.py

…

screws_tilt_adjust.py

screws_tilt_adjust: Add DIRECTION parameter to SCREWS_TILT_CALCULATE (#4357)

2021-06-22 15:18:05 -04:00

sdcard_loop.py

loop_sdcard: Add loopable SD card file sections

2021-05-26 11:57:57 -04:00

servo.py

…

shaper_calibrate.py

…

skew_correction.py

…

spi_temperature.py

…

static_digital_output.py

…

statistics.py

…

stepper_enable.py

…

sx1509.py

…

temperature_fan.py

…

temperature_host.py

…

temperature_mcu.py

…

temperature_sensor.py

…

thermistor.py

…

tmc2130.py

…

tmc2208.py

…

tmc2209.py

…

tmc2660.py

…

tmc5160.py

…

tmc_uart.py

…

tmc.py

…

tsl1401cl_filament_width_sensor.py

…

tuning_tower.py

…

verify_heater.py

…

virtual_sdcard.py

virtual_sdcard: add file_path and file_size to status

2021-06-22 15:15:03 -04:00

z_tilt.py

z_tilt: expose an 'applied' status to allow macros to skip QGL/Z_TILT_ADJUST (#4313)

2021-06-02 11:11:19 -04:00