CreatBotKlipper

display

menu: use MOVE=1 for offset_z menu

2019-07-31 11:17:31 -04:00

__init__.py

…

ad5206.py

…

adc_temperature.py

…

bed_mesh.py

…

bed_screws.py

bed_screws: No need to re-raise an EndstopError

2019-06-06 10:08:58 -04:00

bed_tilt.py

…

bltouch.py

homing: Implement homing via new toolhead "drip" movement

2019-07-10 10:43:20 -04:00

bus.py

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

buttons.py

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

controller_fan.py

…

delayed_gcode.py

delayed_gcode: initial implementation

2019-07-01 11:09:30 -04:00

delta_calibrate.py

…

dotstar.py

neopixel: Use low priority for LED updates

2019-08-06 22:25:26 -04:00

endstop_phase.py

endstop_phase: Add tmc2209 and tmc5160 to list of tmc drivers

2019-06-23 11:27:18 -04:00

fan.py

…

filament_switch_sensor.py

filament_switch_sensor: add SET_FILAMENT_SENSOR gcode

2019-07-10 09:57:46 -04:00

firmware_retraction.py

firmware_retract: Remove z_hop support

2019-07-10 19:25:56 -04:00

force_move.py

…

gcode_button.py

gcode_button: Execute gcode when a button is pressed or released (#1745 )

2019-06-21 18:06:31 -04:00

gcode_macro.py

gcode_macro: add iterator to status wrapper

2019-07-01 10:59:13 -04:00

heater_bed.py

…

heater_fan.py

…

heater_generic.py

…

homing_override.py

homing_override: Pass params to template evaluation

2019-06-09 11:14:31 -04:00

idle_timeout.py

gcode: Eliminate the process_batch() method

2019-06-09 18:44:44 -04:00

manual_probe.py

manual_probe: Add extra checks to catch manual probe not finishing correctly

2019-06-06 10:08:58 -04:00

manual_stepper.py

…

mcp4018.py

…

mcp4451.py

…

mcp4728.py

mcp4728: Update to better match printrbot revf requirements

2019-07-26 11:02:56 -04:00

multi_pin.py

…

neopixel.py

neopixel: Use low priority for LED updates

2019-08-06 22:25:26 -04:00

output_pin.py

…

pause_resume.py

pause_resume: add CLEAR_PAUSE gcode

2019-06-28 12:44:49 -04:00

pid_calibrate.py

…

probe.py

probe: Rework the PROBE_ACCURACY command parameters

2019-07-10 15:21:09 -04:00

quad_gantry_level.py

quad_gantry_level: Support retries

2019-06-18 12:12:25 -04:00

query_endstops.py

mcu: Integrate query_endstop_wait() into query_endstop()

2019-07-10 10:43:20 -04:00

replicape.py

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

respond.py

…

samd_sercom.py

…

screws_tilt_adjust.py

…

servo.py

…

skew_correction.py

skew_correction: add SKEW_PROFILE gcode

2019-06-29 10:58:46 -04:00

spi_temperature.py

serialhdl: Rename register_callback() to register_response()

2019-06-21 18:14:00 -04:00

static_digital_output.py

…

statistics.py

…

sx1509.py

sx1509: Minor cleanup - don't default print_time to 0

2019-06-25 18:19:05 -04:00

temperature_fan.py

temperature_fan: Remove executable flag from temperature_fan.py

2019-06-10 14:30:48 -04:00

temperature_sensor.py

…

thermistor.py

…

tmc2130.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc2208.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc2209.py

tmc_uart: Add support for configuring the uart address on tmc2209 chips

2019-07-31 13:02:27 -04:00

tmc2660.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc5160.py

tmc: Configure "intpol" field from TMCMicrostepHelper

2019-06-28 16:59:26 -04:00

tmc_uart.py

tmc_uart: Make sure address is at least 0

2019-07-31 13:13:27 -04:00

tmc.py

mcu: Integrate query_endstop_wait() into query_endstop()

2019-07-10 10:43:20 -04:00

tsl1401cl_filament_width_sensor.py

…

verify_heater.py

verify_heater: Don't raise a heater error if the heater is off

2019-06-12 22:06:54 -04:00

virtual_sdcard.py

gcode: Eliminate the process_batch() method

2019-06-09 18:44:44 -04:00

z_tilt.py

z_tilt: Support retries

2019-06-18 12:12:25 -04:00