CreatBot/CreatBotKlipper
CreatBot/CreatBotKlipper
7
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
CreatBotKlipper/src
History
Kevin O'Connor 2469356861 stm32f1: Add support for building with a 0x7000 code offset 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-23 13:36:15 -04:00
..
atsam
atsam: Enable pullup on i2c SDA line
2019-05-23 09:32:10 -04:00
atsamd
atsamd: Minor whitespace changes to sercom.c
2019-04-04 18:30:05 -04:00
avr
avr: Simplify spi mode setting
2019-05-07 23:02:20 -04:00
generic
command: Always pass a string to the DECL_CONSTANT() macro
2019-03-17 19:38:18 -04:00
linux
linux: add support for Linux hardware PWM
2019-04-05 19:06:15 -04:00
lpc176x
lpc176x: refactor usbserial to use udelay helper.
2019-04-06 20:53:15 -04:00
pru
pru: The TMR_CNT is cleared by writing all ones
2019-03-31 13:48:50 -04:00
simulator
simulator: Wrap code to 80 columns
2019-02-27 14:20:15 -05:00
stm32f0
stm32f0: Wrong port definition for GPIOF (#1463)
2019-03-29 09:41:05 -04:00
stm32f1
stm32f1: Add support for building with a 0x7000 code offset
2019-05-23 13:36:15 -04:00
adccmds.c
adccmds: Run gpio_adc_setup() before oid_alloc()
2019-01-13 11:03:30 -05:00
basecmd.c
command: Always pass a string to the DECL_CONSTANT() macro
2019-03-17 19:38:18 -04:00
basecmd.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
buttons.c
buttons: Wrap code to 80 columns
2019-02-27 14:20:15 -05:00
byteorder.h
byteorder: Add a header file defining common byteswap functions
2018-05-21 09:44:40 -04:00
command.c
command: Wait to send ack until after processing commands
2018-05-28 10:43:40 -04:00
command.h
msgproto: Convert static strings to a more generic enumeration system
2019-03-17 19:38:18 -04:00
compiler.h
compiler.h: Check if __aligned and __section macros are already defined
2016-06-13 23:18:59 -04:00
ctr.h
command: Support evaluating C expressions in DECL_CONSTANT()
2019-03-17 19:38:18 -04:00
debugcmds.c
debugcmds: Add support for reading/writing 32bit values
2019-02-07 11:50:14 -05:00
endstop.c
endstop: Use "pin_value" instead of "pin" when querying endstop state
2019-03-19 10:48:33 -04:00
gpiocmds.c
command: Always pass a string to the DECL_CONSTANT() macro
2019-03-17 19:38:18 -04:00
i2ccmds.c
bus: Change bus parameter in config_spi/config_i2c
2019-04-04 18:29:31 -04:00
initial_pins.c
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
initial_pins.h
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
Kconfig
stm32f0: New target STM32F0 added.
2019-03-24 12:10:11 -04:00
lcd_hd44780.c
lcd_hd44780: Add micro-controller code for the HD44780 LCD chip
2018-03-06 11:30:34 -05:00
lcd_st7920.c
lcd_st7920: Use a longer delay at the start of each command/data
2018-06-22 23:47:09 -04:00
Makefile
initial_pins: Add ability to configure output pins at mcu startup
2019-03-17 20:56:25 -04:00
pwmcmds.c
pwmcmds: allow 16-bit resolution
2019-04-05 19:02:48 -04:00
sched.c
sched: Force sched_try_shutdown to be inlined
2018-10-13 11:47:00 -04:00
sched.h
pru: Support config_reset command to manually reset mcu
2017-09-03 23:16:38 -04:00
spi_software.c
spi_software: Minor simplification to spi_software_prepare()
2019-05-22 11:40:30 -04:00
spi_software.h
spi_software: Implementation of software spi
2019-02-13 11:52:20 -05:00
spicmds.c
bus: Change bus parameter in config_spi/config_i2c
2019-04-04 18:29:31 -04:00
spicmds.h
thermocouple: Add initial support for common SPI temperature sensing chips
2018-07-24 11:16:05 -04:00
stepper.c
stepper: Fix reset_step_clock corruption due to bitset typo
2019-03-19 20:57:17 -04:00
stepper.h
stepper: Introduce stepper_get_position command and remove from endstop.c
2017-03-09 14:54:52 -05:00
thermocouple.c
thermocouple: Define thermocouple types using enumerations
2019-03-17 19:38:18 -04:00
tmcuart.c
pins: Add support for pull down resistors
2019-02-27 11:13:21 -05:00