Florian Heilmann 64e6d85898 sam4e8e: Add the SAM4e8e port ...

This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD

Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>

2018-08-08 10:44:49 -04:00

..

avr

atmega1284p: Add choice between UART0 or UART1 to Kconfig

2018-07-13 19:58:04 -04:00

generic

armcm_irq: Enhance clear_active_irq() so it works on cortex-m0

2018-08-06 23:36:05 -04:00

linux

linux: Add support for bi-directional SPI communication

2018-07-24 11:16:05 -04:00

lpc176x

usb_cdc: Allow USB endpoint ids to be board specific

2018-08-06 23:36:05 -04:00

pru

pru: Disable ADC reading directly from the PRU

2018-06-27 12:10:25 -04:00

sam3x8e

sam3x8e: Use SAM3X CMSIS files instead of arduino CMSIS files

2018-08-06 23:36:05 -04:00

sam4e8e

sam4e8e: Add the SAM4e8e port

2018-08-08 10:44:49 -04:00

samd21

samd21: Minor fixes to usbserial

2018-08-08 10:43:57 -04:00

simulator

simulator: Rework dummy simulator code to user timer_irq / serial_irq

2018-07-11 14:35:24 -04:00

stm32f1

stm32f1: implement spi_prepare

2018-07-08 09:25:11 -04:00

adccmds.c

adccmds: Add support for min/max temperature check filtering

2018-07-02 13:56:34 -04:00

basecmd.c

basecmd: Rename get_status to get_clock

2018-05-29 10:57:29 -04:00

basecmd.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

buttons.c

buttons: Add initial support for detecting button presses

2018-06-30 14:28:51 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

build: Avoid linker magic in compile_time_request.c unique id generation

2017-05-26 12:32:02 -04:00

debugcmds.c

debugcmds: Move debugging commands from basecmd.c to new file

2017-05-15 14:02:59 -04:00

endstop.c

endstop: Eliminate end_stop_set_oversample command

2017-10-12 11:59:27 -04:00

gpiocmds.c

gpiocmds: Add update_digital_out command

2018-06-27 12:10:39 -04:00

Kconfig

sam4e8e: Add the SAM4e8e port

2018-08-08 10:44:49 -04:00

lcd_hd44780.c

lcd_hd44780: Add micro-controller code for the HD44780 LCD chip

2018-03-06 11:30:34 -05:00

lcd_st7920.c

lcd_st7920: Use a longer delay at the start of each command/data

2018-06-22 23:47:09 -04:00

Makefile

thermocouple: Add initial support for common SPI temperature sensing chips

2018-07-24 11:16:05 -04:00

pwmcmds.c

gpiocmds: Allow the start value for a pin to differ from the default_value

2017-10-12 11:59:27 -04:00

sched.c

sched: Interrupts must be disabled during setjmp() call

2017-12-21 12:54:33 -05:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spicmds.c

thermocouple: Add initial support for common SPI temperature sensing chips

2018-07-24 11:16:05 -04:00

spicmds.h

thermocouple: Add initial support for common SPI temperature sensing chips

2018-07-24 11:16:05 -04:00

stepper.c

stepper: Introduce and use gpio_out_toggle_noirq()

2018-05-15 17:09:11 -04:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Minor fixes

2018-07-25 09:06:50 -04:00