CreatBot/CreatBotKlipper
CreatBot/CreatBotKlipper
7
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
CreatBotKlipper/config
History
Kevin O'Connor 7327394c50 adc_temperature: Add support for linear interpolation of resistances 
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 21:28:25 -05:00
..
avrsim.cfg
…
example-corexy.cfg
…
example-delta.cfg
…
example-extras.cfg
adc_temperature: Add support for linear interpolation of resistances
2019-01-21 21:28:25 -05:00
example-menu.cfg
menu: enhancements
2019-01-07 21:39:50 -05:00
example-multi-mcu.cfg
…
example-polar.cfg
polar: Experimental support for polar kinematics
2018-12-24 11:38:59 -05:00
example-winch.cfg
winch: Add experimental support for cable winch kinematics
2018-12-24 11:38:59 -05:00
example.cfg
extruder: Don't use max_extrude_cross_section in max_extrude_only defaults
2018-10-25 19:09:47 -04:00
generic-bigtreetech-skr-v1.1.cfg
config: Generic board BIGTREETECH SKR V1.1 config
2019-01-16 09:40:15 -05:00
generic-cramps.cfg
…
generic-duet2.cfg
tmc2660: Use bus.py helper code for spi
2018-11-21 12:12:31 -05:00
generic-einsy-rambo.cfg
…
generic-fysetc-f6.cfg
config: Create generic-fysetc-f6.cfg
2019-01-10 09:55:54 -05:00
generic-melzi.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
generic-mini-rambo.cfg
…
generic-minitronics1.cfg
config: Add a generic-minitronics1.cfg example config file
2018-12-20 11:09:20 -05:00
generic-printrboard.cfg
mcp4728: Add initial support for the mcp4728 i2c dac chip
2019-01-02 18:17:56 -05:00
generic-radds.cfg
config: Added encoder pins to radds example config
2019-01-02 17:46:06 -05:00
generic-rambo.cfg
…
generic-ramps.cfg
config: pin mapping for ender 3 stock display and encoder on ramps (#1075)
2019-01-06 11:51:27 -05:00
generic-re-arm.cfg
…
generic-replicape.cfg
…
generic-rumba.cfg
config: Add lcd encoder pins to generic-rumba.cfg
2018-10-28 14:34:22 -04:00
generic-smoothieboard.cfg
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
2019-01-07 20:00:44 -05:00
kit-voron2-2018.cfg
…
printer-adimlab-2018.cfg
config: ADIMlab Add support for LCD knob and caselight
2018-10-19 11:10:32 -04:00
printer-anet-a8-2017.cfg
…
printer-anet-e10-2018.cfg
…
printer-anycubic-i3-mega-2017.cfg
…
printer-anycubic-kossel-2016.cfg
config: Make the Anycubic delta configurations as similar as possible
2018-11-25 17:14:16 -05:00
printer-anycubic-kossel-plus-2017.cfg
config: Make the Anycubic delta configurations as similar as possible
2018-11-25 17:14:16 -05:00
printer-creality-cr10-2017.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
printer-creality-cr10mini-2017.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
printer-creality-cr10s-2017.cfg
config: Add display buttons to printer-creality-cr10s-2017.cfg
2018-10-20 19:27:53 -04:00
printer-creality-cr20-2018.cfg
config: Fix CR-20 click pin polarity
2018-12-15 18:38:03 -05:00
printer-creality-ender2-2017.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
printer-creality-ender3-2018.cfg
config: Update printer-creality-ender3-2018.cfg (#959)
2018-12-05 16:43:14 -05:00
printer-lulzbot-taz6-2017.cfg
…
printer-makergear-m2-2012.cfg
endstop_phase: Move endstop phase homing code to new "extras" module
2018-10-16 13:09:23 -04:00
printer-micromake-d1-2016.cfg
config: Add printer-micromake-d1-2016.cfg example config file
2018-12-18 20:59:43 -05:00
printer-seemecnc-rostock-max-v2-2015.cfg
…
printer-tronxy-x5s-2018.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
printer-tronxy-x8-2018.cfg
…
printer-velleman-k8200-2013.cfg
config: Add printer-velleman-k8200-2013.cfg example config
2018-11-13 10:46:57 -05:00
printer-wanhao-duplicator-6-2016.cfg
…
printer-wanhao-duplicator-i3-plus-2017.cfg
…
printer-wanhao-duplicator-i3-v2.1-2017.cfg
config: Use consistent advice on flashing the Melzi board
2018-11-13 14:32:52 -05:00
sample-macros.cfg
config: sample-macros.cfg creation and M300
2018-11-13 12:42:10 -05:00
sample-probe-as-z-endstop.cfg
config: Update sample-probe-as-z-endstop.cfg to use set_position_z=0
2019-01-07 10:26:04 -05:00