Kevin O'Connor 94dc8167c9 z_tilt: Don't default "points" parameter to "z_positions" parameter ...

It's rare to have all the Z stepper locations directly under the
printable surface, so using z_positions for points is not a good
default.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2018-07-15 10:30:27 -04:00

..

display

docs: Add display g-code commands to docs/G-Codes.md

2018-07-08 10:12:23 -04:00

__init__.py

…

ad5206.py

spicmds: Rework SPI message transmission

2018-05-07 09:10:34 -04:00

adc_temperature.py

adccmds: Add support for min/max temperature check filtering

2018-07-02 13:56:34 -04:00

bed_tilt.py

gcode: Rename run_script() to run_script_from_command()

2018-06-30 14:08:02 -04:00

buttons.py

buttons: Improve rotary encoder handler by using Ben Buxton state machine. (#445)

2018-07-01 08:41:14 -04:00

delta_calibrate.py

delta: Minor change to get_position_from_stable()

2018-07-14 11:55:15 -04:00

fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

gcode_macro.py

gcode: Rename run_script() to run_script_from_command()

2018-06-30 14:08:02 -04:00

heater_bed.py

heater: Add PrinterHeaters class that stores all sensors and heaters

2018-04-04 23:13:53 -04:00

heater_fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

homing_override.py

gcode: Rename run_script() to run_script_from_command()

2018-06-30 14:08:02 -04:00

mcp4451.py

mcp4451: Add initial support for programming the mcp4451 on lpc176x

2018-06-29 21:20:12 -04:00

multi_pin.py

pins: Remove module level get_printer_pins() and setup_pin() functions

2018-04-04 12:26:39 -04:00

output_pin.py

output_pin: Fix SET_PIN max_val check

2018-06-05 09:12:31 -04:00

pid_calibrate.py

heater: Introduce smooth_time config option; remove pid_deriv_time

2018-07-06 13:47:10 -04:00

probe.py

probe: Make sure there are at least 3 points even if using default_points

2018-07-14 15:33:58 -04:00

replicape.py

linux: Convert linux SPI code to use the generic spicmds.c code

2018-05-07 09:10:34 -04:00

servo.py

servo: Use new gcode.register_mux_command()

2018-05-20 12:40:10 -04:00

static_digital_output.py

static_digital_output: Add static_digital_output section to extras/

2018-03-17 13:06:51 -04:00

stepper_buzz.py

mcu: Enhance itersolve stepper kinematics allocation

2018-07-13 11:37:36 -04:00

temperature_fan.py

temperature_fan: Fix issue 403 use max_speed

2018-06-19 11:51:07 -04:00

thermistor.py

adccmds: Add support for min/max temperature check filtering

2018-07-02 13:56:34 -04:00

tmc2130.py

tmc2130: Add a DUMP_TMC helper command

2018-06-30 19:01:56 -04:00

verify_heater.py

verify_heater: Disable when writing output to a debug file

2018-06-08 23:51:41 -04:00

virtual_sdcard.py

gcode: Raise an error if a duplicate command is registered

2018-05-20 13:08:22 -04:00

z_tilt.py

z_tilt: Don't default "points" parameter to "z_positions" parameter

2018-07-15 10:30:27 -04:00