CreatBotKlipper

History

Kevin O'Connor a7c8476e98 docs: Update pressure advance doc to note it only impacts the extruder

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2018-10-25 19:09:47 -04:00

img

docs: Add Delta_Calibrate.md guide with "enhanced delta calibration"

2018-09-25 13:48:46 -04:00

prints

delta_calibrate: Initial support for enhanced delta calibration

2018-09-25 13:48:46 -04:00

beaglebone.md

pru: Disable ADC reading directly from the PRU

2018-06-27 12:10:25 -04:00

Bootloaders.md

docs: Updates to stm32f103 benchmarks

2018-10-11 10:57:24 -04:00

Code_Overview.md

docs: Add a section with micro-controller porting tips to Code_Overview.md

2018-07-11 14:40:39 -04:00

Config_checks.md

docs: Add an Endstop_Phase.md document

2018-10-16 13:09:49 -04:00

Contact.md

docs: Expand on why it is important to provide the log in Contact.md

2018-07-08 20:30:35 -04:00

CONTRIBUTING.md

docs: Add a CONTRIBUTING document

2017-12-24 12:33:01 -05:00

Debugging.md

docs: Fix SAM4E8E benchmark test revision

2018-10-22 11:21:43 -04:00

Delta_Calibrate.md

delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE

2018-10-22 11:26:01 -04:00

developer-certificate-of-origin

docs: Add a CONTRIBUTING document

2017-12-24 12:33:01 -05:00

Endstop_Phase.md

tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816 )

2018-10-24 16:01:12 -04:00

FAQ.md

docs: Add a "Lost communication with MCU" section to the FAQ

2018-10-09 11:22:28 -04:00

Features.md

docs: Update SAM4E8E benchmarks

2018-10-22 11:18:55 -04:00

G-Codes.md

bed_mesh: Do not automatically run G28 on BED_MESH_CALIBRATE / BED_MESH_MAP

2018-10-22 11:26:01 -04:00

Installation.md

gcode: Send proactive state messages

2018-09-12 21:31:27 -04:00

issue_template.md

docs: Add github issue template

2018-01-31 14:30:05 -05:00

Kinematics.md

docs: Minor change to wording of junction speeds

2018-08-03 15:48:07 -04:00

MCU_Commands.md

basecmd: Rename get_status to get_clock

2018-05-29 10:57:29 -04:00

Overview.md

docs: Add an Endstop_Phase.md document

2018-10-16 13:09:49 -04:00

Pressure_Advance.md

docs: Update pressure advance doc to note it only impacts the extruder

2018-10-25 19:09:47 -04:00

Protocol.md

docs: Replace get_status example with get_clock in Protocol.md

2018-10-20 11:53:32 -04:00

README.md

docs: Improve documentation for those starting in docs/

2017-04-27 16:05:26 -04:00

Releases.md

docs: Update release notes for v0.6.0 release

2018-03-31 14:04:39 -04:00

stm32f1.md

docs: Update stm32f1.md - usb is now supported.

2018-10-22 13:22:58 -04:00

README.md

Welcome to the Klipper documentation. The overview document is a good starting point.