Kevin O'Connor c3efcd9c8d bus: Set all SPI CS pins high before first config_spi message ...

If an SPI device is shared among many devices, then all the device's
CS pins should be set high prior to setting up the clk pin.
(Otherwise, there's a chance a device could interpret the clk pin
setup as part of a transmission.)

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-01-04 22:26:34 -05:00

..

display

display: Fix handling of M117 command if lowercase 'm' is used

2019-01-02 17:34:56 -05:00

__init__.py

…

ad5206.py

ad5206: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

adc_temperature.py

adc_temperature: Minor whitespace changes

2018-07-26 10:51:48 -04:00

bed_mesh.py

bed_mesh: Introduce fade_target option

2018-11-30 11:37:21 -05:00

bed_tilt.py

bed_tilt: Do not automatically run G28 on BED_TILT_CALIBRATE

2018-10-22 11:26:01 -04:00

bltouch.py

bltouch: Issue both a "reset" and a "pin_up" after a successful probe

2018-12-16 11:06:46 -05:00

bus.py

bus: Set all SPI CS pins high before first config_spi message

2019-01-04 22:26:34 -05:00

buttons.py

mcu: Rename add_config_object() to register_config_callback()

2018-09-03 11:48:22 -04:00

delta_calibrate.py

delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE

2018-10-22 11:26:01 -04:00

endstop_phase.py

tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816)

2018-10-24 16:01:12 -04:00

fan.py

…

force_move.py

force_move: Provide defaults for SET_KINEMATIC_POSITION parameters

2018-08-02 08:58:18 -04:00

gcode_macro.py

gcode_macro: Provide more information on a formatting error

2018-09-30 12:43:54 -04:00

heater_bed.py

heater: take a gcode_id when setting up a heater (#1028)

2019-01-02 17:44:02 -05:00

heater_fan.py

heater_fan: Allow multiple heaters to be defined for a heater_fan

2018-08-17 10:20:12 -04:00

homing_override.py

gcode: Rename run_script() to run_script_from_command()

2018-06-30 14:08:02 -04:00

idle_timeout.py

idle_timeout: Add printing/ready/idle tracking

2018-10-28 18:39:45 -04:00

mcp4451.py

mcp4451: Minor update - remove unnecessary mcu import

2018-11-24 00:36:49 -05:00

mcp4728.py

mcp4728: Add initial support for the mcp4728 i2c dac chip

2019-01-02 18:17:56 -05:00

multi_pin.py

pins: Explicitly pass can_invert and can_pullup to lookup_pin()

2018-07-26 09:44:45 -04:00

output_pin.py

output_pin: Fix SET_PIN max_val check

2018-06-05 09:12:31 -04:00

pid_calibrate.py

pid_calibrate: Add some comments on the calibration methodology

2018-10-19 22:40:11 -04:00

probe.py

bltouch: Add initial support for a bltouch "extras" module

2018-11-30 11:34:20 -05:00

quad_gantry_level.py

probe: Support manual probing at runtime

2018-10-01 11:12:30 -04:00

query_endstops.py

query_endstops: Move QUERY_ENDSTOP command to it own extras/ module

2018-07-16 10:06:30 -04:00

replicape.py

replicape: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

respond.py

respond: An extra for sending messages to the printer host. (#1053)

2019-01-02 17:45:35 -05:00

servo.py

servo: This patch create ability to enable/disable attached servo. (#880)

2018-11-14 09:38:09 -05:00

spi_temperature.py

spi_temperature: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

static_digital_output.py

static_digital_output: Add static_digital_output section to extras/

2018-03-17 13:06:51 -04:00

statistics.py

statistics: Move stats handling to new "extras" module

2018-09-02 13:46:19 -04:00

sx1509.py

sx1509: Relax restrictions on SX1509 pins (#836)

2018-10-30 18:08:12 -04:00

temperature_fan.py

temperature_fan: Fix issue 403 use max_speed

2018-06-19 11:51:07 -04:00

thermistor.py

thermistor: Avoid divide by zero error if min_temp=-273.15

2019-01-04 12:47:37 -05:00

tmc2130.py

tmc2130: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

tmc2208.py

tmc2208: error raise fixed for rx/tx mcu check

2018-12-27 11:44:41 -05:00

tmc2660.py

tmc2660: error and whitespace fixes

2018-12-27 11:44:41 -05:00

verify_heater.py

verify_heater: Don't report a heater error if printer is shutdown

2018-09-30 10:40:44 -04:00

virtual_sdcard.py

gcode: process_batch() should execute commands atomically

2018-10-28 18:39:45 -04:00

z_tilt.py

z_tilt: Wrap lines to 80 columns

2018-10-01 11:12:30 -04:00