Arksine d350e2c617 display: add M117 "show message" support ...

When M117 is followed by an empty string, the display will reset to
Klipper's default.

Internal modules may look up the display and directly call
set_message(), with a timeout if desired.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>

2018-06-27 12:33:25 -04:00

..

__init__.py

…

ad5206.py

spicmds: Rework SPI message transmission

2018-05-07 09:10:34 -04:00

adc_temperature.py

adc_temperature: Support defining custom sensors in the config file

2018-04-09 15:44:34 -04:00

bed_tilt.py

probe: Rename get_position() callback to get_probed_position()

2018-06-22 15:33:12 -04:00

delta_calibrate.py

probe: Rename get_position() callback to get_probed_position()

2018-06-22 15:33:12 -04:00

display.py

display: add M117 "show message" support

2018-06-27 12:33:25 -04:00

fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

gcode_macro.py

gcode_macro: Add the ability to define custom g-code macros

2018-05-25 12:40:06 -04:00

heater_bed.py

heater: Add PrinterHeaters class that stores all sensors and heaters

2018-04-04 23:13:53 -04:00

heater_fan.py

fan: Allow the fan shutdown_speed to be configured

2018-05-18 19:12:03 -04:00

homing_override.py

homing_override: Add axes config parameter

2018-06-11 20:41:18 -04:00

multi_pin.py

pins: Remove module level get_printer_pins() and setup_pin() functions

2018-04-04 12:26:39 -04:00

output_pin.py

output_pin: Fix SET_PIN max_val check

2018-06-05 09:12:31 -04:00

pid_calibrate.py

pid_calibrate: Make sure to unregister new control class on error

2018-04-06 11:39:24 -04:00

probe.py

probe: Rename get_position() callback to get_probed_position()

2018-06-22 15:33:12 -04:00

replicape.py

linux: Convert linux SPI code to use the generic spicmds.c code

2018-05-07 09:10:34 -04:00

servo.py

servo: Use new gcode.register_mux_command()

2018-05-20 12:40:10 -04:00

static_digital_output.py

static_digital_output: Add static_digital_output section to extras/

2018-03-17 13:06:51 -04:00

stepper_buzz.py

stepper: Don't peak into PrinterStepper members

2018-06-22 14:09:01 -04:00

temperature_fan.py

temperature_fan: Fix issue 403 use max_speed

2018-06-19 11:51:07 -04:00

thermistor.py

thermistor: Add Honeywell 100K and MGB18 thermistor definitions

2018-04-30 16:08:17 -04:00

tmc2130.py

tmc2130: Allow the PWMCONF register to be configured

2018-05-25 11:38:27 -04:00

verify_heater.py

verify_heater: Disable when writing output to a debug file

2018-06-08 23:51:41 -04:00

virtual_sdcard.py

gcode: Raise an error if a duplicate command is registered

2018-05-20 13:08:22 -04:00

z_tilt.py

probe: Rename get_position() callback to get_probed_position()

2018-06-22 15:33:12 -04:00