CreatBotKlipper

display

font8x14: Store font as strings instead of as bytearray

2019-02-27 13:26:59 -05:00

__init__.py

…

ad5206.py

ad5206: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

adc_temperature.py

heater: Rename add_sensor() to add_sensor_factory()

2019-02-25 20:34:12 -05:00

bed_mesh.py

bed_mesh: simplify configuration

2019-02-25 13:34:14 -05:00

bed_screws.py

bed_screws: Add a helper tool for leveling bed screws

2019-02-24 00:49:47 -05:00

bed_tilt.py

klippy: Convert printer_state("connect") to an event handler

2019-01-08 11:09:55 -05:00

bltouch.py

bltouch: Issue just a pin_up command on a normal raise probe attempt

2019-02-04 18:03:07 -05:00

bus.py

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

buttons.py

…

controller_fan.py

controller_fan: Add support for a fan cooling the controller-board (#1070 )

2019-01-10 12:12:15 -05:00

delta_calibrate.py

delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE

2018-10-22 11:26:01 -04:00

endstop_phase.py

tmc2660: Add endstop phase detection functionality to TMC2660 extra (#816 )

2018-10-24 16:01:12 -04:00

fan.py

gcode: Use an event to handle restart request actions

2019-02-25 21:26:27 -05:00

force_move.py

…

gcode_macro.py

gcode: Raise a config error on invalid register_command()

2019-02-18 18:04:42 -05:00

heater_bed.py

heater_bed: Wrap lines to 80 columns

2019-02-26 11:20:01 -05:00

heater_fan.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

heater_generic.py

heater: Support generic gcode_id registration for sensors

2019-02-26 12:07:00 -05:00

homing_override.py

…

idle_timeout.py

idle_timeout: Added a missing logging import

2019-01-29 11:18:44 -05:00

manual_probe.py

gcode: Raise a config error on invalid register_command()

2019-02-18 18:04:42 -05:00

manual_stepper.py

manual_stepper: Add an "extras" module for manually controlling a stepper

2019-02-12 13:38:13 -05:00

mcp4018.py

mcp4018: Add initial support for the mcp4018 digipot

2019-02-16 08:16:37 -05:00

mcp4451.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

mcp4728.py

mcp4728: Add initial support for the mcp4728 i2c dac chip

2019-01-02 18:17:56 -05:00

multi_pin.py

…

output_pin.py

…

pause_resume.py

pause_resume: fixes

2019-02-08 10:53:59 -05:00

pid_calibrate.py

pid_calibrate: Add some comments on the calibration methodology

2018-10-19 22:40:11 -04:00

probe.py

probe: Set z min value in probe_accuracy to z_offset. (#1314 )

2019-02-25 12:52:54 -05:00

quad_gantry_level.py

klippy: Convert printer_state("connect") to an event handler

2019-01-08 11:09:55 -05:00

query_endstops.py

…

replicape.py

replicape: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

respond.py

respond: An extra for sending messages to the printer host. (#1053 )

2019-01-02 17:45:35 -05:00

servo.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

spi_temperature.py

spi_temperature: Wrap code to 80 columns

2019-02-27 13:14:23 -05:00

static_digital_output.py

…

statistics.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

sx1509.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

temperature_fan.py

temperature_fan: Remove stats as it now supports gcode reports

2019-02-26 12:07:00 -05:00

temperature_sensor.py

temperature_sensor: Add generic temperature sensor support

2019-02-26 13:15:56 -05:00

thermistor.py

heater: Rename add_sensor() to add_sensor_factory()

2019-02-25 20:34:12 -05:00

tmc2130.py

tmc2130: Use FieldHelper() to set/get driver fields

2019-02-21 11:35:58 -05:00

tmc2208.py

tmc2130: Use FieldHelper() to set/get driver fields

2019-02-21 11:35:58 -05:00

tmc2660.py

tmc2660: error and whitespace fixes

2018-12-27 11:44:41 -05:00

tsl1401cl_filament_width_sensor.py

gcode: Raise a config error on invalid register_command()

2019-02-18 18:04:42 -05:00

verify_heater.py

klippy: Convert printer_state("connect") to an event handler

2019-01-08 11:09:55 -05:00

virtual_sdcard.py

virtual_sdcard: Don't list files starting with a '.'

2019-02-08 11:48:53 -05:00

z_tilt.py

klippy: Convert printer_state("connect") to an event handler

2019-01-08 11:09:55 -05:00