Douglas Hammond b6589406d4 temperature_sensor: Add generic temperature sensor support ...

Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-02-26 13:15:56 -05:00

..

avrsim.cfg

…

example-corexy.cfg

…

example-delta.cfg

…

example-extras.cfg

temperature_sensor: Add generic temperature sensor support

2019-02-26 13:15:56 -05:00

example-menu.cfg

menu: enhancements

2019-01-07 21:39:50 -05:00

example-multi-mcu.cfg

…

example-polar.cfg

polar: Experimental support for polar kinematics

2018-12-24 11:38:59 -05:00

example-winch.cfg

winch: Add experimental support for cable winch kinematics

2018-12-24 11:38:59 -05:00

example.cfg

config: Warn that cycle_time may not match when using hardware_pwm

2019-02-19 13:19:32 -05:00

generic-azteeg-x5-mini-v3.cfg

config: Azteeg X5 mini config (#1193)

2019-02-08 15:00:23 -05:00

generic-bigtreetech-skr-v1.1.cfg

config: Update generic-bigtreetech-skr-v1.1 (#1209)

2019-02-07 18:16:07 -05:00

generic-cramps.cfg

…

generic-duet2.cfg

tmc2660: Use bus.py helper code for spi

2018-11-21 12:12:31 -05:00

generic-einsy-rambo.cfg

…

generic-fysetc-f6.cfg

config: Update generic-fysetc-f6.cfg display section

2019-02-07 18:23:17 -05:00

generic-gt2560.cfg

config: Added example config file for Geeetech gt2560 controller.

2019-01-28 11:20:01 -05:00

generic-melzi.cfg

config: Use consistent advice on flashing the Melzi board

2018-11-13 14:32:52 -05:00

generic-mini-rambo.cfg

…

generic-minitronics1.cfg

config: Add a generic-minitronics1.cfg example config file

2018-12-20 11:09:20 -05:00

generic-printrboard.cfg

mcp4728: Add initial support for the mcp4728 i2c dac chip

2019-01-02 18:17:56 -05:00

generic-radds.cfg

config: Added encoder pins to radds example config

2019-01-02 17:46:06 -05:00

generic-rambo.cfg

…

generic-ramps.cfg

config: pin mapping for ender 3 stock display and encoder on ramps (#1075)

2019-01-06 11:51:27 -05:00

generic-re-arm.cfg

…

generic-replicape.cfg

…

generic-rumba.cfg

…

generic-smoothieboard.cfg

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

kit-voron2-250mm.cfg

config: Example config file for a stock 250mm build VORON2 printer

2019-02-13 12:07:20 -05:00

printer-adimlab-2018.cfg

…

printer-anet-a8-2017.cfg

…

printer-anet-e10-2018.cfg

…

printer-anycubic-i3-mega-2017.cfg

config: Add a "printer-" prefix to example printer config files

2018-02-11 14:58:48 -05:00

printer-anycubic-kossel-2016.cfg

config: Make the Anycubic delta configurations as similar as possible

2018-11-25 17:14:16 -05:00

printer-anycubic-kossel-plus-2017.cfg

config: Make the Anycubic delta configurations as similar as possible

2018-11-25 17:14:16 -05:00

printer-creality-cr10-2017.cfg

config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds

2019-02-08 12:20:16 -05:00

printer-creality-cr10mini-2017.cfg

config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds

2019-02-08 12:20:16 -05:00

printer-creality-cr10s-2017.cfg

config: Use "ATC Semitec 104GT-2" for CR10 (and similar) heater beds

2019-02-08 12:20:16 -05:00

printer-creality-cr20-2018.cfg

config: Fix CR-20 click pin polarity

2018-12-15 18:38:03 -05:00

printer-creality-ender2-2017.cfg

config: Use consistent advice on flashing the Melzi board

2018-11-13 14:32:52 -05:00

printer-creality-ender3-2018.cfg

config: Update printer-creality-ender3-2018.cfg (#959)

2018-12-05 16:43:14 -05:00

printer-lulzbot-taz6-2017.cfg

…

printer-makergear-m2-2012.cfg

…

printer-micromake-d1-2016.cfg

config: Add printer-micromake-d1-2016.cfg example config file

2018-12-18 20:59:43 -05:00

printer-seemecnc-rostock-max-v2-2015.cfg

…

printer-tronxy-x5s-2018.cfg

config: Use consistent advice on flashing the Melzi board

2018-11-13 14:32:52 -05:00

printer-tronxy-x8-2018.cfg

…

printer-velleman-k8200-2013.cfg

config: Add printer-velleman-k8200-2013.cfg example config

2018-11-13 10:46:57 -05:00

printer-wanhao-duplicator-6-2016.cfg

…

printer-wanhao-duplicator-i3-plus-2017.cfg

…

printer-wanhao-duplicator-i3-v2.1-2017.cfg

config: Use consistent advice on flashing the Melzi board

2018-11-13 14:32:52 -05:00

sample-macros.cfg

pause_resume: update documentation

2019-01-28 11:23:52 -05:00

sample-probe-as-z-endstop.cfg

config: Update sample-probe-as-z-endstop.cfg to use set_position_z=0

2019-01-07 10:26:04 -05:00