CreatBotKlipper

History

menu: changes in tune menu according to #4023 (#4086 )

- set 1% as input minimum for speed and flow
- set speed maximum from 200% to 500%

Signed-off-by: Janar Sööt <janar.soot@gmail.com>

2021-03-23 10:55:25 -04:00

display

menu: changes in tune menu according to #4023 (#4086 )

2021-03-23 10:55:25 -04:00

__init__.py

…

ad5206.py

…

adc_scaled.py

…

adc_temperature.py

…

adxl345.py

…

bed_mesh.py

…

bed_screws.py

…

bed_tilt.py

…

bltouch.py

…

bme280.py

bme280: Add support for BMP280 and BME680 sensors (#4040 )

2021-03-15 11:50:29 -04:00

board_pins.py

…

bus.py

tmc2130: Verify SPI register writes

2021-03-10 17:12:25 -05:00

buttons.py

…

canbus_ids.py

mcu: Add support for connecting to devices on a CAN bus

2021-03-13 11:29:41 -05:00

controller_fan.py

…

delayed_gcode.py

…

delta_calibrate.py

…

display_status.py

…

dotstar.py

…

ds18b20.py

…

endstop_phase.py

…

extruder_stepper.py

…

fan_generic.py

…

fan.py

fan: Minor updates to tachometer handling

2021-03-01 14:57:40 -05:00

filament_motion_sensor.py

filament_motion_sensor: Add filament_motion_sensor (#3857 )

2021-03-14 21:36:19 -04:00

filament_switch_sensor.py

…

firmware_retraction.py

…

force_move.py

…

gcode_arcs.py

…

gcode_button.py

…

gcode_macro.py

…

gcode_move.py

…

hall_filament_width_sensor.py

…

heater_bed.py

heaters: Make sure set_temp() command wakes up the idle_timeout

2021-03-05 18:59:01 -05:00

heater_fan.py

…

heater_generic.py

…

heaters.py

heaters: Make sure set_temp() command wakes up the idle_timeout

2021-03-05 18:59:01 -05:00

homing_heaters.py

…

homing_override.py

…

homing.py

…

htu21d.py

htu21d: sensor definition fix (#4075 )

2021-03-18 23:38:07 -04:00

idle_timeout.py

idle_timeout: change standard timeout g-code (#4018 )

2021-03-07 13:48:54 -05:00

input_shaper.py

…

lm75.py

…

manual_probe.py

…

manual_stepper.py

…

mcp4018.py

…

mcp4451.py

…

mcp4728.py

…

multi_pin.py

…

neopixel.py

…

output_pin.py

…

pause_resume.py

…

pid_calibrate.py

heaters: Make sure set_temp() command wakes up the idle_timeout

2021-03-05 18:59:01 -05:00

print_stats.py

…

probe.py

…

pulse_counter.py

fan: Minor updates to tachometer handling

2021-03-01 14:57:40 -05:00

quad_gantry_level.py

…

query_adc.py

…

query_endstops.py

…

replicape.py

…

resonance_tester.py

…

respond.py

…

safe_z_home.py

…

samd_sercom.py

…

save_variables.py

…

screws_tilt_adjust.py

…

servo.py

…

shaper_calibrate.py

graph_accelerometer: Support axis-level comparison of adxl345 data

2021-03-20 13:24:43 -04:00

skew_correction.py

…

spi_temperature.py

…

static_digital_output.py

…

statistics.py

…

stepper_enable.py

…

sx1509.py

…

temperature_fan.py

…

temperature_host.py

…

temperature_mcu.py

…

temperature_sensor.py

…

thermistor.py

…

tmc2130.py

tmc2130: Report CS_ACTUAL in DUMP_TMC even if zero

2021-03-16 11:31:24 -04:00

tmc2208.py

…

tmc2209.py

…

tmc2660.py

tmc2660: Fix typo in seup field

2021-03-18 23:36:25 -04:00

tmc5160.py

tmc: Fix order of init during sensorless homing

2021-02-28 18:30:25 -05:00

tmc_uart.py

tmc_uart: Limit to only one active uart at a time on an mcu

2021-03-12 20:51:11 -05:00

tmc.py

tmc: Only check for tmc2130 reset via CS_ACTUAL if IHOLD > 0

2021-03-15 13:48:58 -04:00

tsl1401cl_filament_width_sensor.py

…

tuning_tower.py

…

verify_heater.py

…

virtual_sdcard.py

…

z_tilt.py

…