Kevin O'Connor f2ca7d5c66 verify_heater: Improve handling of new targets when temperature is dropping ...

Allow the first check_gain_time interval to only require a
heating_gain relative to the lowest observed temperature during that
interval.  This makes the code less likely to raise a spurious error
when the heater is enabled while the heater temperature is dropping.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2019-03-08 10:55:46 -05:00

..

display

gcode: Change respond_info() to log by default

2019-03-04 13:04:18 -05:00

__init__.py

…

ad5206.py

…

adc_temperature.py

heater: Rename add_sensor() to add_sensor_factory()

2019-02-25 20:34:12 -05:00

bed_mesh.py

bed_mesh: simplify configuration

2019-02-25 13:34:14 -05:00

bed_screws.py

bed_screws: Fix missing import

2019-02-28 00:30:05 -05:00

bed_tilt.py

klippy: Convert printer_state("connect") to an event handler

2019-01-08 11:09:55 -05:00

bltouch.py

gcode: Change respond_info() to log by default

2019-03-04 13:04:18 -05:00

bus.py

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

buttons.py

buttons: Wrap code to 80 columns

2019-02-27 13:34:22 -05:00

controller_fan.py

controller_fan: Add support for a fan cooling the controller-board (#1070)

2019-01-10 12:12:15 -05:00

delta_calibrate.py

…

endstop_phase.py

…

fan.py

Wrap code to 80 columns

2019-02-27 13:27:52 -05:00

filament_switch_sensor.py

filament_switch_sensor: initial implementation of switch based filament runout/insert sensor

2019-03-01 00:45:51 -05:00

force_move.py

manual_stepper: Add support for moves with acceleration

2019-03-03 13:38:10 -05:00

gcode_macro.py

gcode: Raise a config error on invalid register_command()

2019-02-18 18:04:42 -05:00

heater_bed.py

heater_bed: Wrap lines to 80 columns

2019-02-26 11:20:01 -05:00

heater_fan.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

heater_generic.py

heater: Support generic gcode_id registration for sensors

2019-02-26 12:07:00 -05:00

homing_override.py

…

idle_timeout.py

idle_timeout: Added a missing logging import

2019-01-29 11:18:44 -05:00

manual_probe.py

gcode: Raise a config error on invalid register_command()

2019-02-18 18:04:42 -05:00

manual_stepper.py

manual_stepper: Add support for moves with acceleration

2019-03-03 13:38:10 -05:00

mcp4018.py

mcp4018: Add initial support for the mcp4018 digipot

2019-02-16 08:16:37 -05:00

mcp4451.py

i2ccmds: Pass the i2c address as a 7-bit number (0-127)

2019-01-07 20:00:44 -05:00

mcp4728.py

mcp4728: Add initial support for the mcp4728 i2c dac chip

2019-01-02 18:17:56 -05:00

multi_pin.py

…

output_pin.py

…

pause_resume.py

pause_resume: Implement send_pause_command()

2019-03-01 00:45:51 -05:00

pid_calibrate.py

…

probe.py

probe: Wrap code to 80 columns

2019-02-27 13:28:55 -05:00

quad_gantry_level.py

quad_gantry_level: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

query_endstops.py

…

replicape.py

…

respond.py

respond: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

samd_sercom.py

atsamd: Add support for programming SERCOM pins

2019-03-01 00:40:44 -05:00

servo.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

spi_temperature.py

spi_temperature: Wrap code to 80 columns

2019-02-27 13:14:23 -05:00

static_digital_output.py

…

statistics.py

klippy: Convert printer_state("ready") to an event handler

2019-01-08 10:59:43 -05:00

sx1509.py

sx1509: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

temperature_fan.py

temperature_fan: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

temperature_sensor.py

temperature_sensor: Add generic temperature sensor support

2019-02-26 13:15:56 -05:00

thermistor.py

thermistor: Wrap code to 80 columns

2019-02-27 13:29:41 -05:00

tmc2130.py

gcode: Change respond_info() to log by default

2019-03-04 13:04:18 -05:00

tmc2208.py

gcode: Change respond_info() to log by default

2019-03-04 13:04:18 -05:00

tmc2660.py

tmc2660: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

tsl1401cl_filament_width_sensor.py

tsl1401cl_filament_width_sensor: Wrap code to 80 columns

2019-02-27 14:33:17 -05:00

verify_heater.py

verify_heater: Improve handling of new targets when temperature is dropping

2019-03-08 10:55:46 -05:00

virtual_sdcard.py

pause_resume: Implement send_pause_command()

2019-03-01 00:45:51 -05:00

z_tilt.py

gcode: Change respond_info() to log by default

2019-03-04 13:04:18 -05:00