Matt Baker
f2fbe98454
bed_mesh: enable relative offset bed meshes ( #1323 ) ...
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.
Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
2019-03-21 10:39:22 -04:00
2018-01-12 16:44:21 -05:00
2018-02-25 16:00:55 -05:00
2019-03-08 11:47:17 -05:00
2019-03-21 10:39:22 -04:00
2019-01-07 21:39:50 -05:00
2018-06-01 17:22:03 -04:00
2018-12-24 11:38:59 -05:00
2018-12-24 11:38:59 -05:00
2019-03-17 21:07:31 -04:00
2019-03-08 22:22:41 -05:00
2019-02-07 18:16:07 -05:00
2018-06-27 12:10:25 -04:00
2019-03-08 11:04:14 -05:00
2018-05-25 11:38:23 -04:00
2019-02-07 18:23:17 -05:00
2019-01-28 11:20:01 -05:00
2018-11-13 14:32:52 -05:00
2018-09-11 09:40:48 -04:00
2018-12-20 11:09:20 -05:00
2019-03-14 10:44:02 -04:00
2019-01-02 17:46:06 -05:00
2018-03-06 13:15:09 -05:00
2019-01-06 11:51:27 -05:00
2019-03-08 22:22:41 -05:00
2018-03-17 12:55:48 -04:00
2019-03-14 11:48:25 -04:00
2019-03-08 22:22:41 -05:00
2019-02-13 12:07:20 -05:00
2018-10-19 11:10:32 -04:00
2018-04-09 16:24:14 -04:00
2018-06-19 11:36:52 -04:00
2018-02-11 14:58:48 -05:00
2018-11-25 17:14:16 -05:00
2018-11-25 17:14:16 -05:00
2019-02-08 12:20:16 -05:00
2019-02-08 12:20:16 -05:00
2019-02-08 12:20:16 -05:00
2018-12-15 18:38:03 -05:00
2018-11-13 14:32:52 -05:00
2018-12-05 16:43:14 -05:00
2018-03-06 11:30:46 -05:00
2018-10-16 13:09:23 -04:00
2018-12-18 20:59:43 -05:00
2018-02-11 14:58:48 -05:00
2019-03-14 10:27:37 -04:00
2019-03-01 00:09:30 -05:00
2018-07-10 11:59:07 -04:00
2018-11-13 10:46:57 -05:00
2018-09-25 14:29:05 -04:00
2018-02-25 16:00:55 -05:00
2018-11-13 14:32:52 -05:00
2019-01-28 11:23:52 -05:00
2019-01-07 10:26:04 -05:00
f2fbe98454