diff --git a/docs/Panels.md b/docs/Panels.md
index 6b216011..52d6e626 100644
--- a/docs/Panels.md
+++ b/docs/Panels.md
@@ -15,18 +15,6 @@ panel: bed_level
 ```
 ![Bed Level](img/panels/bed_level.png)
 
-The bed level panel has the ability to have preset locations from Klipper. Please see documentation on the following
-Klipper Sections:
-* [bed_screws](https://www.klipper3d.org/Config_Reference.html#bed_screws)
-* [screws_tilt_adjust](https://www.klipper3d.org/Config_Reference.html#screws_tilt_adjust)
-
-!!! important:
-    `[bed_screws]` uses Nozzle positions and `[screws_tilt_adjust]` uses Probe positions
-
-This panel will use `[bed_screws]` if `[screws_tilt_adjust]` is not defined,
-the probe offset will be applied to the defined screw values in `[screws_tilt_adjust]`
-so the buttons will move the nozzle above the screws like in `[bed_screws]`
-
 ### Bed Mesh
 ```py
 panel: bed_mesh
diff --git a/docs/Screws.md b/docs/Screws.md
new file mode 100644
index 00000000..c96a62a6
--- /dev/null
+++ b/docs/Screws.md
@@ -0,0 +1,43 @@
+# Bed level
+
+![Bed Level](img/panels/bed_level.png)
+
+For this panel to appear in the menu `[bed_screws]` or `[screws_tilt_adjust]` need to be defined in Klipper config (printer.cfg)
+
+!!! Important
+    * `[bed_screws]` uses nozzle positions (nozzle above the screw) [Read Klipper doc entry](https://www.klipper3d.org/Config_Reference.html#bed_screws)
+    * `[screws_tilt_adjust]` uses probe positions (probe above the screw) [Read Klipper doc entry](https://www.klipper3d.org/Config_Reference.html#screws_tilt_adjust)
+
+
+The corner buttons in KlipperScreen place the nozzle above the screw to do the ["paper test"](https://www.klipper3d.org/Bed_Level.html?h=paper#the-paper-test).
+
+When `[screws_tilt_adjust]` is defined a couple of things happen:
+
+* A button named "Screws adjust" appears, it runs `SCREWS_TILT_CALCULATE` when is pressed,
+and reports the amount to be adjusted into the labels of the corner buttons.
+* `[bed_screws]` is now ignored by KlipperScreen. (explained below)
+* The corner buttons are now `[screws_tilt_adjust]` coordinates with the probe offset applied. (explained below)
+
+### Why `[bed_screws]` are ignored/not used?
+
+Because if the probe offset is changed or the difference between `[bed_screws]` and `[screws_tilt_adjust]` wasn't calculated correctly,
+the "Screws adjust" button stops working.
+
+
+### Why the probe offset is applied to `[screws_tilt_adjust]`?
+
+Because the corner buttons in KlipperScreen should place the nozzle above the screw to do the ["paper test"](https://www.klipper3d.org/Bed_Level.html?h=paper#the-paper-test). It doesn't affect the function of `SCREWS_TILT_CALCULATE`, which will go to the defined positions.
+
+## Not supported for auto-detection
+
+This message will appear if you are using 3 or 5 screws and didn't define them in KlipperScreen.conf.
+See "screw_positions" in the [printer options](https://klipperscreen.readthedocs.io/en/latest/Configuration/#printer-options)
+
+## Limitations
+
+The panel doesn't support more than 8 screws or screws that directly in the center of the bed.
+
+## Is there an alternative?
+
+If you have a reliable probe, define `[bed_mesh]` in Klipper config, remove the springs
+and use some thread-locker or locking nuts to fix the bed to the gantry, let the probe do a mesh save it and forget about this.
diff --git a/mkdocs.yml b/mkdocs.yml
index 4702e82b..cdcf533d 100644
--- a/mkdocs.yml
+++ b/mkdocs.yml
@@ -7,6 +7,7 @@ repo_name: jordanruthe/KlipperScreen/
 repo_url: https://github.com/jordanruthe/KlipperScreen/
 nav:
     - Home: index.md
+    - Bed Level/Screws: Screws.md
     - Setup:
       - Hardware.md
       - Installation.md