#: panels/print.py:229
msgid "?"
msgstr ""

#: panels/zcalibrate.py:65
msgid "Abort"
msgstr "Abort"

#: panels/zcalibrate.py:61
msgid "Accept"
msgstr ""

#: panels/print.py:229
msgid "Are you sure you want to print"
msgstr ""

#: panels/job_status.py:108
msgid "Are you sure you wish to cancel this print?"
msgstr ""

#: panels/bed_level.py:89 panels/fan.py:52 panels/fine_tune.py:119
#: panels/menu.py:18 panels/move.py:96 panels/network.py:34
#: panels/preheat.py:54 panels/temperature.py:78
msgid "Back"
msgstr ""

#: panels/job_status.py:79 panels/print.py:225
msgid "Cancel"
msgstr ""

#: panels/fan.py:42
msgid "Cancel Change"
msgstr ""

#: panels/job_status.py:111
msgid "Cancel Print"
msgstr ""

#: panels/temperature.py:146
msgid "Close"
msgstr ""

#: panels/job_status.py:85
msgid "Control"
msgstr ""

#: panels/preheat.py:51
msgid "Cooldown"
msgstr ""

#: panels/temperature.py:49
msgid "Decrease"
msgstr ""

#: panels/bed_level.py:79
msgid "Disable XY"
msgstr ""

#: panels/zcalibrate.py:57
msgid "Distance (mm)"
msgstr ""

#: panels/bed_level.py:85 panels/job_status.py:82
msgid "Emergency Stop"
msgstr ""

#: panels/extrude.py:32
msgid "Extrude"
msgstr ""

#: panels/fine_tune.py:66 panels/fine_tune.py:134
msgid "Extrusion"
msgstr ""

#: panels/fine_tune.py:64
msgid "Extrusion +"
msgstr ""

#: panels/fine_tune.py:68
msgid "Extrusion -"
msgstr ""

#: panels/fine_tune.py:46 panels/fine_tune.py:141
msgid "Fan"
msgstr ""

#: panels/fine_tune.py:44
msgid "Fan +"
msgstr ""

#: panels/fine_tune.py:48
msgid "Fan -"
msgstr ""

#: panels/fan.py:32
msgid "Fan Off"
msgstr ""

#: panels/fan.py:35
msgid "Fan On"
msgstr ""

#: panels/extrude.py:21 panels/extrude.py:25
msgid "Fast"
msgstr ""

#: panels/system.py:22 panels/splash_screen.py:59
msgid "Firmware Restart"
msgstr ""

#: panels/job_status.py:115
msgid "Go Back"
msgstr ""

#: panels/bed_level.py:76 panels/move.py:38
msgid "Home All"
msgstr ""

#: panels/zcalibrate.py:25
msgid "Homing"
msgstr ""

#: panels/temperature.py:47
msgid "Increase"
msgstr ""

#: panels/splash_screen.py:23
msgid "Initializing printer..."
msgstr ""

#: panels/system.py:20
msgid "Klipper Restart"
msgstr ""

#: panels/system.py:43 panels/system.py:42
msgid "KlipperScreen Version"
msgstr ""

#: panels/system.py:62
msgid "Load Average"
msgstr ""

#: panels/zcalibrate.py:34
msgid "Lower Nozzle"
msgstr ""

#: panels/extrude.py:20 panels/extrude.py:21 panels/extrude.py:24
msgid "Medium"
msgstr ""

#: panels/move.py:87
msgid "Move Distance (mm)"
msgstr ""

#: panels/network.py:28
msgid "Network Info"
msgstr ""

#: panels/temperature.py:51
msgid "Number Pad"
msgstr ""

#: panels/job_status.py:70
msgid "Pause"
msgstr ""

#: panels/print.py:224
msgid "Print"
msgstr ""

#: panels/print.py:154
msgid "Print Time"
msgstr ""

#: panels/zcalibrate.py:32
msgid "Raise Nozzle"
msgstr ""

#: panels/splash_screen.py:57
msgid "Restart"
msgstr ""

#: panels/job_status.py:68
msgid "Resume"
msgstr ""

#: panels/extrude.py:34
msgid "Retract"
msgstr ""

#: panels/fan.py:39
msgid "Set Speed"
msgstr ""

#: panels/print.py:152
msgid "Size"
msgstr ""

#: panels/extrude.py:21 panels/extrude.py:23
msgid "Slow"
msgstr ""

#: panels/fine_tune.py:56 panels/fine_tune.py:137
msgid "Speed"
msgstr ""

#: panels/fine_tune.py:54
msgid "Speed +"
msgstr ""

#: panels/fine_tune.py:58
msgid "Speed -"
msgstr ""

#: panels/system.py:31 panels/system.py:30
msgid "System Information"
msgstr ""

#: panels/extrude.py:36
msgid "Temperature"
msgstr ""

#: panels/job_status.py:33 panels/job_status.py:34
msgid "Time Elapsed"
msgstr ""

#: panels/job_status.py:35 panels/job_status.py:36
msgid "Time Left"
msgstr ""

#: panels/extrude.py:30
msgid "Tool 1"
msgstr ""

#: panels/print.py:150
msgid "Uploaded"
msgstr ""

#: panels/move.py:23
msgid "X+"
msgstr ""

#: panels/move.py:25
msgid "X-"
msgstr ""

#: panels/move.py:28
msgid "Y+"
msgstr ""

#: panels/move.py:30
msgid "Y-"
msgstr ""

#: panels/fine_tune.py:35 panels/fine_tune.py:131 panels/zcalibrate.py:23
msgid "Z Offset"
msgstr ""

#: panels/fine_tune.py:33 panels/move.py:33
msgid "Z+"
msgstr ""

#: panels/fine_tune.py:37 panels/move.py:35
msgid "Z-"
msgstr ""

#: panels/fine_tune.py:35
msgid "mm"
msgstr ""