Kevin O'Connor d6c2e24f4c tmc5160: Support setting GLOBALSCALER to fine tune current selection ...

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2020-03-04 19:40:32 -05:00

..

display

menu: Set speed for move actions (#2520)

2020-02-17 20:52:54 -05:00

__init__.py

…

ad5206.py

…

adc_temperature.py

…

bed_mesh.py

…

bed_screws.py

…

bed_tilt.py

…

bltouch.py

bltouch: BTLOUCH V3.0/V3.1 Enable 5V/OD mode set commands (#2540)

2020-02-23 22:32:07 -05:00

bme280.py

bme280: handle read timeout exceptions

2020-02-14 17:25:08 -05:00

board_pins.py

…

bus.py

mcu: Introduce new lookup_query_command() command wrapper

2020-02-20 13:24:53 -05:00

buttons.py

…

controller_fan.py

…

delayed_gcode.py

…

delta_calibrate.py

…

dotstar.py

…

endstop_phase.py

homing: Add a "home_rails_begin" event notifier

2020-02-15 17:52:44 -05:00

extruder_stepper.py

…

fan.py

…

filament_switch_sensor.py

filament_switch_sensor: Query "printing" status instead of tracking it

2020-02-17 17:07:54 -05:00

firmware_retraction.py

…

force_move.py

…

gcode_arcs.py

…

gcode_button.py

…

gcode_macro.py

gcode_macro: Support overriding of builtin g-code commands

2020-02-12 20:42:03 -05:00

hall_filament_width_sensor.py

hall_filament_width_sensor: Added virtual runout sensor (#2535)

2020-03-01 22:05:12 -05:00

heater_bed.py

…

heater_fan.py

…

heater_generic.py

…

homing_heaters.py

homing: Merge home_prepare()/home_finalize() into move_begin/move_end events

2020-02-15 17:52:44 -05:00

homing_override.py

…

idle_timeout.py

…

manual_probe.py

…

manual_stepper.py

manual_stepper: Support ignoring errors on STOP_ON_ENDSTOP

2020-02-19 13:38:22 -05:00

mcp4018.py

…

mcp4451.py

…

mcp4728.py

…

multi_pin.py

…

neopixel.py

…

output_pin.py

…

pause_resume.py

…

pid_calibrate.py

…

probe.py

homing: Don't raise a TimeoutError from home_wait()

2020-02-19 12:20:00 -05:00

quad_gantry_level.py

…

query_adc.py

…

query_endstops.py

query_endstops: Add get_status() method that reports the last query state

2020-02-12 19:32:48 -05:00

replicape.py

…

respond.py

…

safe_z_home.py

safe_z_home: Support note_z_not_homed() in kinematics (#2500)

2020-03-01 23:00:41 -05:00

samd_sercom.py

…

screws_tilt_adjust.py

…

servo.py

…

skew_correction.py

…

spi_temperature.py

…

static_digital_output.py

…

statistics.py

…

stepper_enable.py

…

sx1509.py

…

temperature_fan.py

heater: Fix misspelling of Celsius

2020-02-27 11:31:51 -05:00

temperature_sensor.py

heater: Fix misspelling of Celsius

2020-02-27 11:31:51 -05:00

thermistor.py

heater: Fix misspelling of Celsius

2020-02-27 11:31:51 -05:00

tmc2130.py

…

tmc2208.py

…

tmc2209.py

…

tmc2660.py

…

tmc5160.py

tmc5160: Support setting GLOBALSCALER to fine tune current selection

2020-03-04 19:40:32 -05:00

tmc_uart.py

mcu: Introduce new lookup_query_command() command wrapper

2020-02-20 13:24:53 -05:00

tmc.py

tmc: Revert incorrect changes to TPWMTHRS setting

2020-02-20 11:41:35 -05:00

tsl1401cl_filament_width_sensor.py

…

tuning_tower.py

…

verify_heater.py

…

virtual_sdcard.py

…

z_tilt.py

…